Search UandiStar
2
I. Microprocessor 8086 :
1. Introduction to MASM/TASM.
2. Arithmetic operation – Multi byte Addition and Subtraction, Multiplication and Division – Signed and
unsigned Arithmetic operation, ASCII – arithmetic operation.
3. Logic operations – Shift and rotate – Converting packed BCD to unpacked BCD, BCD to ASCII
conversion.
4. By using string operation and Instruction prefix: Move Block, Reverse string, Sorting, Inserting, Deleting,
Length of the string, String comparison.
5. DOS/BIOS programming: Reading keyboard (Buffered with and without echo) – Display characters,
Strings.
II. Interfacing :
1. 8259 – Interrupt Controller : Generate an interrupt using 8259 timer.
2. 8279 – Keyboard Display : Write a small program to display a string of characters.
3. 8255 – PPI : Write ALP to generate sinusoidal wave using PPI.
4. 8251 – USART : Write a program in ALP to establish Communication between two processors.
III. Microcontroller 8051
1. Reading and Writing on a parallel port.
2. Timer in different modes.
3. Serial communication implementation.
Equipment required for Laboratories:
1. 8086 μP Kits
2. 8051 Micro Controller kits
3. Interfaces/peripheral subsystems
i) 8259 PIC
ii) 8279-KB/Display
iii) 8255 PPI
iv) 8251 USART
4. ADC Interface
5. DAC Interface
6. Traffic Controller Interface
7. Elevator Interface
Download MICROPROCESSORS AND INTERFACING (MPI) LAB Manual including VIVA Questions
MICROPROCESSORS AND INTERFACING (MPI) LAB Manual including VIVA Questions
MICROPROCESSORS AND INTERFACING (MPI) LAB Manual including VIVA Questions
I. Microprocessor 8086 :
1. Introduction to MASM/TASM.
2. Arithmetic operation – Multi byte Addition and Subtraction, Multiplication and Division – Signed and
unsigned Arithmetic operation, ASCII – arithmetic operation.
3. Logic operations – Shift and rotate – Converting packed BCD to unpacked BCD, BCD to ASCII
conversion.
4. By using string operation and Instruction prefix: Move Block, Reverse string, Sorting, Inserting, Deleting,
Length of the string, String comparison.
5. DOS/BIOS programming: Reading keyboard (Buffered with and without echo) – Display characters,
Strings.
II. Interfacing :
1. 8259 – Interrupt Controller : Generate an interrupt using 8259 timer.
2. 8279 – Keyboard Display : Write a small program to display a string of characters.
3. 8255 – PPI : Write ALP to generate sinusoidal wave using PPI.
4. 8251 – USART : Write a program in ALP to establish Communication between two processors.
III. Microcontroller 8051
1. Reading and Writing on a parallel port.
2. Timer in different modes.
3. Serial communication implementation.
Equipment required for Laboratories:
1. 8086 μP Kits
2. 8051 Micro Controller kits
3. Interfaces/peripheral subsystems
i) 8259 PIC
ii) 8279-KB/Display
iii) 8255 PPI
iv) 8251 USART
4. ADC Interface
5. DAC Interface
6. Traffic Controller Interface
7. Elevator Interface
Download MICROPROCESSORS AND INTERFACING (MPI) LAB Manual including VIVA Questions
Subscribe to:
Post Comments (Atom)
2 Responses to “MICROPROCESSORS AND INTERFACING (MPI) LAB Manual including VIVA Questions”
May 14, 2013 at 2:18 PM
I want to learn how to make programming in microprocessor. . . . . .plz give me any idea for programming. . . . . . . . .and what is the main part in microprocessor. . . . . .i am doing engineering in 4th semester . . .and branch electronics and communication. . . . .mpi is very critical subject for me. . . . . .special programe. . . .
May 14, 2013 at 2:19 PM
Plz give me any idea mpi programming. . . . . . .
Post a Comment
Add your valuable comment here, ask any questions about this post,
Share your opinions here.
Dont write any Phone numbers in comment...